Ok i have just got a anytone 6666 some manuals say 10amp draw some say 15amp draw , my quistion is
My socket in the car is marked 12v 120watts max
Can i run my rig pluged into it
The fuse in the glove compartment is rated at 20amp
Its nearly new car and would be dificult to run cables from engin bay to inside so looking at the easy way out
Cigar socket to run rig??
-
- Regular
- Posts: 7
- Joined: 29 Apr 2018, 19:12
- Call Sign: 26tm866
- Location: Torbay devon
- Metradio
- Radio Addict
- Posts: 605
- Joined: 28 Apr 2016, 19:10
- Call Sign: G7HID
- Location: Box 500, Slough UK
Re: Cigar socket to run rig??
12v 120wwatt max =10amp max..
Would suggest you look at the size of the wire connecting the fuse box to the Cigar socket, I bet it is woefully thin !
Mike
Would suggest you look at the size of the wire connecting the fuse box to the Cigar socket, I bet it is woefully thin !
Mike
Connect Systems CS750 and CS800, Hytera PD-365, Motorola DP4600.
Raspberry Pi 2 and DV4Mini HotSpot.
AOR AR-DV1 Digital Voice Receiver / eSPY on ARD V1.
Whistler WS1088 / TRX-1 / Whistler Q / UBCD3600XLT / WTR Browser.
Raspberry Pi 2 and DV4Mini HotSpot.
AOR AR-DV1 Digital Voice Receiver / eSPY on ARD V1.
Whistler WS1088 / TRX-1 / Whistler Q / UBCD3600XLT / WTR Browser.
- ch25
- Top Poster
- Posts: 1675
- Joined: 03 Dec 2016, 11:07
- Call Sign: Lemmy
- Location: Poland
Re: Cigar socket to run rig??
No fuse box inside? I would take + lead from there.
6666 and cigar socket can be dangerous.
6666 and cigar socket can be dangerous.
WE ARE MOTÖRHEAD, AND WE PLAY ROCK N' ROLL
You can't have too many antennas...
You can't have too many antennas...
- Mudslinger
- Legend
- Posts: 7490
- Joined: 28 Jul 2010, 07:11
- Location: Oxfordshire
Re: Cigar socket to run rig??
That is assuming that the radio is 100% efficient. It is likely to be around 50% efficient at best, especially if it has Mosfet outputs.
My KL-203p is meant to draw 10A max, but it is more like 16A
Mudslinger - Simon
26TM274
26CT612
There is no such thing as a Fidelity 1000 which is too good to scrap.
26TM274
26CT612
There is no such thing as a Fidelity 1000 which is too good to scrap.
-
- Legend
- Posts: 8666
- Joined: 23 Jan 2010, 19:26
- Location: Bristol-ish
Re: Cigar socket to run rig??
As above, run extra +/- cables from fuse box points or directly from the battery. You can drill a small hole and use a grommet to pass them through unless the car's under warranty or you just can't physically get a drill in. Ensure there's a rated fuse in-line regardless.
-
- Super Member
- Posts: 449
- Joined: 18 May 2011, 22:17
Re: Cigar socket to run rig??
On my motor, there is ducting from the heater unit to the passenger side vent.
A grommet where it enters the cabin and has a rubber nipple.
That's where I'm diving in.
Another problem using the ciggie lighter (caused by the mileage and lack of gauge of the wire) is voltage sag under load.
This will cause FM-ing of the audio on ssb (distortion)
A grommet where it enters the cabin and has a rubber nipple.
That's where I'm diving in.
Another problem using the ciggie lighter (caused by the mileage and lack of gauge of the wire) is voltage sag under load.
This will cause FM-ing of the audio on ssb (distortion)